ACCUMULATION TABLES

• Accumulation Tables, rotary and belt type. (photo)

Back to Table of Contents

Go To Quote Request Page

AIR CLEANERS

• Key Air Cleaner, model 2X, s/s construction, shaker has 1/8" rods with 1/8" spacing, 230/460 volt 3 phase motor, Key Iso Flow gear box model 022812 s/n SH-101596.

Back to Table of Contents

Go To Quote Request Page

BAG DUMPERS

• Semco Systems Bag Dump System, model TBS, w/dust collector, all s/s, size 14A blower with 2HP 3450 rpm 230/460 volt motor  (2 available). (photo)

Back to Table of Contents

Go To Quote Request Page

BAG SEALERS

Back to Table of Contents

Go To Quote Request Page

BAND SEALERS

• Packrite Band Sealer, model 6000-5240-00, 115 volt single phase, s/s adjustable height stand, on casters. Comes with product take away conveyor, 6" wide x 6' long rubber belt, all s/s construction, on casters.

BATTER / BREADING

Back to Table of Contents

Go To Quote Request Page

BEAN EQUIPMENT

Back to Table of Contents

Go To Quote Request Page

BIN DUMPERS

• Bin Dumper, s/s construction, 48" x 48" chamber, pivots at 54". Norman Equipment power pack model NE-93-099A s/n 2968, 2HP 230/460 volt 3 phase.

• Bin Dumper, 54" wide x 39" deep, 8' discharge height, 2HP 230/460 volt self-contained power pack, all s/s construction. Dumper discharges into a 4' x 4' all s/s hopper that slopes down to an 18" x 3' discharge.

Back to Table of Contents

Go To Quote Request Page

BLANCHERS

• Paddle Blancher, 12" x 16', low pressure jacket, hollow flight paddles, s/s contact, s/s bolt down covers, insulated trough, 7" square end bottom discharge, no motor. (photo)

• Aaron Stainless Steel Double Ribbon Blender, 72 cu. ft., 40" wide x 8' long, 8" diameter center bottom discharge, 20HP (2 units). (photo)

• Breddo Likwifier, model LDT 600, s/n D188494-03114, 600 gallon capacity, dual 40HP motors, 230/460 volt, 3 phase, 2 1/2" outlets with Tri-Clamp fittings. Tank is 8' long x 4' wide x 34" deep. (photo)

• Breddo Likwifier, model LOS 1000, s/n D-55638/91200, 1000 gallon capacity, single wall, all s/s construction, (3) 60HP side mount 1770 rpm 230/460 volt 3 phase motors, 3" Tri Clamp outlet with Tri Flo air operated valve.

• CF Howard Paddle Blenders, style #14969, 42" wide x 7' long x 51" deep, 700 gallon capacity, U trough bottom w/ 3" bottom ball valve, all s/s construction, single shaft with 3 sets of paddles, on load cells with Weigh-tronics model WI 125 digital scale head. (photo)

• Lightnin Mixer, model XD-30, s/n 86/809015, s/s shaft with 2 propellers, .30HP 115/230 volt motor, 1725/1424 rpm, on stand with casters. (photo)

• Marion / Mueller Stainless Steel Jacketed Paddle Blender, model T 6239, 12" x 4 1/2', 125 psi dimple jacket with National Board #5757, 6" end bottom discharge, 7.5HP 230/460 volt 1765 rpm motor with vari-speed pulley to Dodge shaft mounted gear reducer size TXT425AS, 24.38 ratio. (photo)

• Marion / Mueller Stainless Steel Jacketed Paddle Blender, model T 6239, 12" x 4 1/2', 125 psi dimple jacket with National Board #6626, 6" end bottom discharge, polished welds, Dodge shaft mounted gear reducer size TDT425, s/n 6212, 24.64 ratio, no tag on motor but looks like 5HP.

• Paddle Blender, 15 cubic foot capacity, all s/s. (photo)

• Kramer-Grebe Bowl Cutter, model CM-325, 325 liter, s/s clad exterior, s/s bowl and s/s knife hood, control panel, 125 HP main knife motor, 5HP bowl drive motor and 1HP unloader variable speed motor with Allen Bradley VFD. Unit has self-contained hydraulics for the unloader & knife cover. Capacity of 620 pounds emulsified product and coarse product capacity of 440 pounds. (photo)

• Chester Jensen Plate Chiller, model XB-3-OT-3-32, 3 plate (2 available).

• Chester Jensen Plate Chiller, model XB-2-OT-2-32, 2 plate (2 available).

• Coating Pan, s/s, 36" diameter x 17" deep drum with 18" wide hole, variable speed drive.

• Charlotte Colloid Mill, model SD 20, s/s product contact, 20HP 3460 rpm 230/460 volt 3 phase motor.

• Allen Kenasco Bin Dump Hopper / Conveyor, 24" wide flighted belt elevator, 2" high flights on 8" centers, 12' long elevator, hydraulic drive.

• Belt Conveyor, 18" wide x 8.5' long, s/s construction, gear head motor drive.

• Belt Conveyor, 28" wide x 18' long, s/s construction, plastic belt, gear head motor drive.

• Cleated Belt Elevated Conveyor, s/s construction, 18" wide x 5' long, 1" cleats on 12" centers, Baldor 1/2HP 230/460 volt gear head motor 1750 rpm with 30 to 1 gear box.

• Incline Belt Conveyor, plastic intralox belt, 12" wide x 12' long, 6' discharge height, s/s infeed hopper, 1HP drive motor, s/s frame, on casters.

• RMF Screw Elevator, model SC1416

, s/n 41473, 14" x 16', all s/s, 24" square feed hopper, 29" infeed height, 10' discharge height (adjustable), 5HP Sterling Electric 230/460 volt motor with gear box, 70 rpm on auger. (photo)

• RMF Screw Elevator, model SC1618

, s/n 41459-1, 16" x 18', all s/s, 36" square feed hopper, 39" infeed height, 10' discharge height (adjustable), 7.5HP Baldor 230/460 volt motor with gear box, 60 rpm on auger. (photo)

• RMF Screw Elevator, model SC1618

, s/n 41459-2, 16" x 18' with 16" pitch, all s/s, 36" square feed hopper, 42" infeed height, 9' 6" discharge height (adjustable), 7.5HP Baldor 230/460 volt 1760 rpm motor to 10 to 1 ratio gear box, 60 rpm on auger. (photo)

• RMF Screw Elevator, model SC1819

, s/n 41455, 18" x 19' with 18" pitch, all s/s, 36" x 24" feed hopper, 36" infeed height, 11' 2" discharge height (adjustable) 35 degree incline, has 2 slots 1" x 27" in trough, 7.5HP 230/460 volt motor with gear box, 63 rpm on auger. (photo)

• Screw Conveyor Elevator, 12" x 14' long, all s/s construction, 8" diameter discharge, 3HP 230/460 volt motor, 12" pitch, hinged cover, 3" bottom cleanout on infeed end, on casters.

• Cornell Versator, model D-16, s/s contacts, 10HP 230/460 volt Reeves vari-speed drive.

DRYERS

• Heinzen Spin Dryer, model SD-300, s/n 1705, s/s construction, hydraulic drive (no power pack), 4 baskets go with the machine, baskets are 30" diameter x 36" deep with 3/16" perforations.

• Heinzen Spin Dryer, model SD-300, s/n 10355-2, s/s construction, hydraulic drive (no power pack), 3 baskets go with the machine, baskets are 30" diameter x 36" deep with 3/16" perforations.

Back to Table of Contents

Go To Quote Request Page

DUMPERS (Bin / Tote / Barrel)

• Bin Dumper, s/s construction, 48" x 48" chamber, pivots at 54". Norman Equipment power pack model NE-93-099A s/n 2968, 2HP 230/460 volt 3 phase.

• Bin Dumper, 54" wide x 39" deep, 8' discharge height, 2HP 230/460 self-contained power pack, all s/s construction Dumper discharges into a 4' x 4' all s/s hopper that slopes down to an 18" x 3' discharge. (photo)

• Tubar Drum Dumper, 110 volt single phase motor on hydraulic pump, 63" high pivot point. (photo)

• SDC 1300 Sanitary Dust Collector, 1300 CFM, 230/460 volt.

• Stephan Emulsifier, model MCH-20, s/n 719-394-04, all s/s, 160m/2A0 3510 rpm 220/440 volt motor, motor #3156446.

• Stephan Emulsifier, model MCD-D150, s/n M05040, all s/s, micro-cut, 225M/2 motor, motor #6793365. Cutting head (outer) 3D0403-02/1.4112/J.02.2007, cutting ring SL.035/0105389.4, head 3D0403-06/1.4112/0114587.5, ring N3.05/0106035.3.

• Magnuson Trough Belt Single File Feeder, model F, 1/2HP gearhead motor.

• Vanmark Potato Slicer Feeder, dual feed rollers, 24" long, s/s, 1/2HP 230/460 volt 3 phase motor (2 units available).

• World Cup Rotary Fill / Seal / Lid System Filler, model 8-12, s/n 1113, 8 station, 2 1/8" diameter pockets, cup dispenser, pre-cut foil "Tamper-Evident" heat seal, s/s hopper.

• Canco Seamer, model PUV, rectangular can.

• Elmar Rotary Piston Filler, model RPE-328C, 28 piston, set 211, 2 3/4" diameter x 8" long pistons, worm to star infeed, counter clockwise rotation. (photo)

• FMC Granular Filler, model 21-G, s/n HR-813, set 300 diameter cans, brush attachment. (photo)

• FMC Rotary Piston Filler, model C-150, set 300 diameter.

• FMC Prevacuumizing Syruper, model 125, s/n 4133, set 603 diameter, 12 station, conveyor / worm / star infeed, star discharge. (photo)

• Modern Packaging Inc. Filler, model SL-1x2, s/n MP-254, 3.5 to 5 lb. tub w/tub dispenser, pneumatic, film or foil heat seal, control panel, 240 volt. (photo)

• Phaudler Rotary Piston Filler w/rising Tables, model RP-1421, s/n R575-0297, 21 station, 3 3/4" pistons, s/s product contact, was running 32 oz. plastic containers, worm to star infeed, star discharge, 7/8" diameter discharge ports, 7" long filling spouts, electro pneumatic no can no fill, pistons have teflon rings top and bottom, 5HP gear head motor drive 1725 rpm 230/460 volt w/Warner brake, gear box was mfg. by Boston and ratio is 15 to 1. (photo)

• Phaudler Rotary Piston Filler, model RP-21, 21 piston, set 401 diameter, square s/s clad base, 3 3/4" diameter x 91/2" long pistons, conveyor / worm / star infeed, counter clockwise rotation. (photo)

• Fitzpatrick Hammer Mill, model DASO 6, s/n 10113, all s/s construction, water cooled bearings, fixed hammers blunt both sides, pan feed to hopper, 10HP 230/460 volt 3485 rpm UL listed motor and controls.

• Ishida Scale, model CCW-S-212 ST, 14 head, smooth buckets, s/n 12958, remote operation, 1191-2380 grams, Heat & Control s/n P-287-860, 8"x 5" x 8" deep buckets, control panel.

• Ishida Scale, model CCW-S-212 ST, 14 head, smooth buckets, s/n 12959, remote operation, 1191-2380 grams, Heat & Control s/n P-287-860, 8" x 5" x 8" deep buckets, control panel.

• Waukesha Cherry Burrell Triple Tube Heat Exchangers, two separate systems configured as follows: quantity 4 each 4" x 3" by 2", 10 each 4" x 3" x 1.5", 13 each 5" x 4" x 2", 9 each 3" x 2.5" x 1.5". Tubes are 20' long overall. These tubes were previously used on a low acid viscous starch based product and include some regeneration. Built to 3A standards.  (photo)

• A and B Process Systems 450 Gallon Processor, s/n 10169303, 100 psi jacket, National Board #121, 2001 vintage, all s/s, single motion scrape agitator, spray ball, 6.6 agitator rpm, cone bottom, 2" outlet with valve, 66" ID x 51" deep. (photo)

• Groen Steam Jacketed Kettle, model N-20, 20 gallon, 80 psi, s/n & National Board #129116, 1 5/8" center bottom outlet, s/s legs, 1986, very good condition. (photo)

• Groen Steam Jacketed Kettle, model DN/TA-100, s/n 00286-1, 100 gallon, scrape agitated tilt kettle with pour lip, 50 psi working pressure, National Board #140401, 2004 vintage, single motion scrape agitator with secondary bar type agitator. Main agitator has 1HP SEW gear head motor, secondary agitator has 2HP SEW gear head motor drive. Both are 230/460 volt 3 phase. 2" discharge with flush type ball valve. Equipped with hydraulic cylinder to lift agitator out and Rice Lake weigh cells model RL35082-N5-2.5K lbs., s/n AA156316. Weigh Tronics WI-127 touch pad controls and AB Panel View 1000. (photo)

• Groen Steam Jacketed Kettle, model INA 150, 150 gallon, single motion slant scrape agitation, 100 psi. (photo)

• Hamilton Steam Jacketed Kettle, model SA, s/n 4930, 150 gallon, double motion scrape agitation, tilt out agitator, 100 psi, 3" center bottom outlet with pneumatic gate discharge, National Board #186.

• Lee Vacuum Pan, model 150 D7S, s/n B799OD1, 150 gallon, 90 psi, scrape agitation, National Board #5561. (photo)

• Breddo Likwifier, model LDT 600, s/n D188494-03114, 600 gallon capacity, dual 40HP motors, 230/460 volt, 3 phase, 2 1/2" outlets with Tri-Clamp fittings. Tank is 8' long x 4' wide x 34" deep. (photo)

• Breddo Likwifier, model LOS 1000, s/n D-55638/91200, 1000 gallon capacity, single wall, all s/s construction, (3) 60HP side mount 1770 rpm 230/460 volt 3 phase motors, 3" Tri Clamp outlet with Tri Flo air operated valve.

Back to Table of Contents

Go To Quote Request Page

METAL DETECTORS

• Goring Kerr 3" Drop Through Metal Detector, model 402-3 with DSP3/S-PSU controls, 120/230 volt. (photo)

• Whallen Palletizer / Depalletizer, with control panel.

• Hobart Batch Peeler, model 6430-T, all s/s construction, 200/230 volt.

• Brown Pulper, model 202, s/n 203-50, s/s product contact, 4 paddles, 30HP 1750 rpm 220/440 volt motor.

• Brown Pulper, model 202, s/n 204-48, s/s product contact, 4 paddles, split covers, 20HP 1750 rpm 220/440 volt motor.

• APV Centrifugal Pump, model 8VS2, 3" in / 2" out Tri-Clamp, 5HP 1745 rpm motor, 230/460 volt.

• Coker Centrifugal Pump, model C216MD, serial number 01-72208A, 3 HP 230/460 volt motor, very good condition.  2 available.  (photo)

• Cornell Single Port Product Pump, model 6NHP-F6K, s/n K2171-13.5, mild steel pump, s/s frame and vortex tank 34" wide x 42" long, 5HP 1725 rpm 230/460 volt 3 phase motor.

• Cornell Single Port Product Pump, model 6NHP-F6K, s/n K2368-13.5, mild steel pump, s/s frame and vortex tank 34" wide x 42" long, 5HP 1725 rpm 230/460 volt 3 phase motor.

• Key-Cornell Hydro Food Pump, 6", model 6NHPF6K, s/n K-1637/13.5, mild steel pump, s/s frame, with s/s vortex hopper, 7.5HP 1170 rpm motor.

• Fristam Centrifugal Pump, model FP1741/185F, serial number 14116001, 5 HP 230/460 volt motor, 2 1/2" in/ 3" out.  (photo)

• Marlen Food Pump, model Opti-150, schematic # B959070A, all s/s construction, touch pad control panel, lower auger hopper, electronic control for speed and pressure, high pressure machine up to 600 psi, up to 10,000 lbs/hr, ratio 3.4 to 1, conical hopper. (photo)

• Sandpiper Diaphram Pump, model SB2-A, type TGN-2-SS, s/n 369701, 3" tri-clamp in / 2 1/2" tri-clamp out, all s/s.

• Waukesha Positive Displacement Pump, model 060, s/n 92267, looks like it was never used, .004 clearance, s/s base, 3HP 1750 rpm vari-speed drive 117 to 469 speed range.

• Waukesha Positive Displacement Pump, model 060, s/n 142868, 5HP gear motor, s/s base.

• Waukesha Positive Displacement Pump, model 060, s/n 175818-95, s/s base, 5HP gear head 208/230/460 volt motor. Unit has Leeson adjustable speed AC motor control.  (photo)

• Waukesha Positive Displacement Pump, model 130, 3" in / out, s/s base w/casters, 5HP 230/460 volt motor w/gear box.

• Waukesha Positive Displacement Pump, model 130, s/n 269620-00, 3" in / out, vented cover, 7.5HP 230/460 volt motor, 1745 rpm, s/s base.

• Waukesha Positive Displacement Pump, model 134, rectangular infeed, 3" bevel seat sanitary outlet, 7.5HP SEW 230/460 volt motor, m/s base, with or without s/s hopper (4' square x 30" high straight side, cone is 36" deep with 60 degree slope to flange that bolts to pump, 8' overall height).

• Waukesha Positive Displacement Pump, model 220, s/n 214920-98, s/s base. (photo)

• Wilden Diaphram Pump, model T8/SAPB/TF/STF, s/n 0020284507, 2" in/out, 316 s/s, item #08-11234, m/o #422040.

• Screw Conveyor, 9" x 16' long, all s/s construction, shaft mounted gear reducer.

• Screw Conveyor, 9" x 10' long, all s/s construction, 2HP gear head motor drive.

• Screw Conveyor, 9" x 5' long, all s/s construction, shaft mounted gear reducer.

• A.K. Robbins Shaker / Sizer, s/n 139604, 1992 vintage, 24" wide x 7' long, all s/s construction, 3/4" perforations in plastic screen, catch pan, Ajax shaker with 1HP 230/460 volt 3 phase 1725 rpm motor.

• Key Shaker, s/s, s/n 12218-1, removable screens, 24" wide x 6' long, size 8DF Ajax, catch pan.

• Key Shaker / Grader, Triple Deck, model #436328-1, s/n 07-181795, 48" wide x 10' long bed, overall length 12', all s/s construction, 2 separations (3 sizes), 3HP 1750 rpm 230/460 volt 3 phase motor Key dula "Iso-Drive", 16" square infeed, bottom deck is solid and discharges out the left looking from the infeed end, center deck has 3/16" perforations and discharges off the end, top deck has 1" square perforations and discharges out the right side. Side discharges are 6" in diameter, perforated sections are 75" long each, has covers. Excellent, like new condition. (photo)

• Key Shaker / Grader, Triple Deck, model #436309-1, s/n 07-181794, 48" wide x 10' long bed, overall length 12', all s/s construction, 2 separations (3 sizes), 3HP 1750 rpm 230/460 volt 3 phase motor Key dula "Iso-Drive", 16" square infeed, bottom deck is solid and discharges out the left looking from the infeed end, center deck has 3/16" perforations and discharges off the end, top deck has 1" square perforations and discharges out the right side. Side discharges are 6" in diameter, perforated sections are 75" long each, has covers. Excellent, like new condition.

• Key Shaker / Grader, Triple Deck, model #436747-1, s/n 08-188972-2, 48" wide x 10' long bed, overall length 12', all s/s construction, 2 separations (3 sizes), 3HP 1750 rpm 230/460 volt 3 phase motor Key, 16" square infeed, bottom deck is solid and discharges out the left looking from the infeed end. This unit is missing the "Iso-Drive, screens and covers. Unit is otherwise in excellent condition. (photo)

• Key Dewatering / Sizing Shaker, s/s, 36" wide x 7' long, 1/16" perforations in screen, size 10DF Ajax, catch pan.

• Key "Iso Flo" Step Deck Shaker / Sizer, model 427148-1, s/n 99-45076, 38" wide x 6' long, has two 24" removable sizing sections, first section sizes 5/16" to 5/8" and the second section sizes 9/16" to 7/8", both sections drop into same catch pan, all s/s, 3/4HP 230/460 volt 1725 rpm motor.

• Key "Iso Flo" Vibratory Dewatering Shaker / Grader, model 427464-1, s/n 99-47926, single deck, 30" wide x 12' long, all s/s construction, 36" solid pan and four 2' long x 30" wide removable sections with 1" diameter perforations, 1HP 230/460 volt motor.

• Key "Iso Flo" Vibratory Shaker, model 427148-1, s/n 93-28916-2, 24" wide x 6' long, has a 4' long solid pan bolted in, 1HP 230/460 volt 1725 rpm motor, m/s frame.

• Key "Iso Flo" Vibratory Transfer Shaker / Conveyor, model 435530-1, s/n 06-163785, 24" wide x 78" long, max stroke 7, all s/s construction, Key "Iso Drive" with 1HP drive motor.

• Key "Iso Flo" Vibratory Conveyor, model 421305-1, s/n 95-13238, 18" wide x 9' long, bias discharge, below bed frame, all s/s construction, Key "Iso Drive" with 1HP motor.

• VAV Scan-Vibro Feed Shaker, type FR, 45" wide x 66" long x 59" discharge height, all s/s construction, rigidized pan with 2 removable 6" wide drain and clean out  sections, 2 shaker motors. (photo)

• Kason Sifter, model K40-2-SS, s/n M-5062, s/s product contact, 3 decks, 2 screens, top cover, 1/3HP 230/460 volt 3 phase motor, new in 2000.

• Kason Sifter, model K40-2-SS, s/n M-5613, s/s product contact, 3 decks, top cover, 1/3HP 230/460 volt 3 phase motor, new bearings in motor and new springs, new in 2001.

• Sweco Sifter-Separator, model LS-30S-666, s/n LS30-578-06, 3 deck, self cleaning screen, s/s product contact, 1/2HP 440 volt 1140 rpm motor, screens are 12M/QSI, m/s base.

• Urschel Comitrol Processor, model 1700, s/n 2082, 30HP 3/60/230/460 volt brake motor, 17" enclosure, 5634 rpm spindle, 3" cutting head (part #66472-3-J-030510- .030 x .510) and impeller #66860 (2) blade, s/s frame and all s/s product contact parts. (photo)

• Urschel Dicer, model G, set for 3/8" dice, factory control panel, safety disconnects, 2HP 230/460 volt motor, all s/s construction, on casters.

• Urschel Dicer, model GA, set for 3/8" dice, factory control panel, safety disconnects, 2HP 230/460 volt motor. (photo)

• Urschel Dicer, model H, set for 3/4" dice, factory control panel, safety disconnects, 2HP 230/460 volt motor, all s/s construction, on casters.

• Urschel Dicer, model M, s/n 361, factory control panel with safety disconnects, set on 1/2" x 1/4" cut, 5HP 230/460 volt motor.

• Urschel Dicer, model RA, factory control panel with safety disconnects, set 3/8" dice, 5HP 230/460 volt motor. Rebuilt with new motor, all new guards and chutes, new bushings, bearings, shafts and knives.

• Urschel Slicer / Shredders, model CC (2 available).

• Urschel Slicer, model OC, 45° angle bias cut, factory control panel with safety disconnects, cutting head, all s/s construction, 2HP 230/460 volt motor.

• Urschel Slicer, model OV, s/n 1101, 22 blade cutting head, factory control panel with safety disconnects, 2HP motor.

• Urschel Slicer, model OV, s/n 1378, s/s, 17 blade cutting head, control panel with interlocks, 2HP brake motor 220/440 volt 3 phase, hold down belt, feed hopper.

• Urschel Strip Cutter, model VSC, s/n 106, factory control panel with safety disconnects, auto feed unit (also comes with a hand feed unit), variable speed controller, all s/s construction, 5HP 230/460 volt motor.

• SWF Tray Former, model 1T6, Nordson series 3500 hot melt glue, PLUS 5000 series control, 440 volt 3 phase 60 cycle motor, 11.9 full load amps, extended tray blank magazine.

• Agri Weld Service 36" diameter Rotary Unscrambler / Lazy Susan, s/s, 1 1/4" lip on OD of disc. 1/3HP 230/460 volt gear head motor, runs on trunions.

• Urschel Comitrol Processor, model 1700, s/n 2082, 30HP 3/60/230/460 volt brake motor, 17" enclosure, 5634 rpm spindle, 3" cutting head (part #66472-3-J-030510- .030 x .510) and impeller #66860 (2) blade, s/s frame and all s/s product contact parts. (photo)

• Urschel Dicer, model G, set for 3/8" dice, factory control panel, safety disconnects, 2HP 230/460 volt motor, all s/s construction, on casters.

• Urschel Dicer, model H, set for 3/4" dice, factory control panel, safety disconnects, 2HP 230/460 volt motor, all s/s construction, on casters.

• Urschel Dicer, model M, s/n 361, factory control panel with safety disconnects, set on 1/2" x 1/4" cut, 5HP 230/460 volt motor.

 Urschel Dicer, model RA, factory control panel with safety disconnects, set 3/8" dice, 5HP 230/460 volt motor. Rebuilt with new motor, all new guards and chutes, new bushings, bearings, shafts and knives.

• Urschel Slicer / Shredders, model CC (2 available).

• Urschel Slicer, model OC, 45° angle bias cut, factory control panel with safety disconnects, cutting head, all s/s construction, 2HP 230/460 volt motor.

• Urschel Slicer, model OV, s/n 1101, 22 blade cutting head, factory control panel with safety disconnects, 2HP motor.

• Urschel Slicer, model OV, s/n 1378, s/s, 17 blade cutting head, control panel with interlocks, 2HP brake motor 220/440 volt 3 phase, hold down belt, feed hopper.

• Urschel Strip Cutter, model VSC, s/n 106, factory control panel with safety disconnects, auto feed unit (also comes with a hand feed unit), variable speed controller, all s/s construction, 5HP 230/460 volt motor.

• Cutting Head Assembly, flat slice, bronze.  (part #22140)

• Cutting Head Assembly, crinkle slice, bronze. (part #22166)

• Cutting Head Assembly, v slice, .125 V, bronze. (part #22170)

• Impeller Drive Assembly, bronze, rebuilt. (part #22172)

• Cutting Head, 3B-010030. (part #66197)

• Cutting Head, 3B-010040. (part #66198)

• Cutting Head, 3B-015015. (part #66787)

• Cutting Head, 3B-020020. (part #66786)

• Cutting Head, 3J-030300. (part #66569)

• Cutting Head, 3K-010020. (part #66752)

• Cutting Head, 3K-015025. (part #66413)

• Cutting Head, 3K-030090U. (part #66770)

• Impeller, 3 paddle, straight, 3". (part #66214)

• Impeller, 3 paddle, forward slant, 3". (part #66590)

• Impeller, 9 paddle, .650 Uni-Cut, Seal. (part #66806)

• Impeller, 9 paddle, .650 Vari-Cut. (part #67004)

• Lower Retaining Ring. (part #62873)

• Stripper Plate, 1/4", s/s. (part #42398)

• Bearing Block, 1/2". (part #13054)

• Bearing Housing. (part #12009)

• Crank Bearing Block, 3/8", 16 knives. (part #13152)

• Crank Bearing Block, 1/2", 12 knives. (part #13048)

• Crank Bearing Block, 5/8", 10 knives. (part #13154)

• Crank Bearing Block, 3/4", 8 knives. (part #13616)

• Gate Extension Strip, 1/8" - 11/32". (part #12187)

• Gate Extension Strip, 3/8" - 15/32". (part #12190)

• Gate Extension Strip, 1/2" - 3/4". (part #12192)

• Hinge Tube, w/bearings. (part #12201)

• Motor, w/brake, 2HP, 184 frame. (part #13754)

• Shaft, main drive. (part #12199)

• Shaft, jack. (part #12200)

• Shaft, impeller. (part #12436)

• Slicing Knife, straight cut. (part #13104)

• Slicing Knife, crinkle cut. (part #14023)

• Slicing Knife, for peaches. (part #13245)

• Slicing Knife Holder, 1/8", s/s. (part #13016)

• Slicing Knife Holder, for peaches. (part #13071)

• Spindle Assembly, circular, 3/4", s/s. (part #13417)

• Spindle Assembly, crosscut, 9/32" (22 knife), s/s. (part #13344)

• Spindle Assembly, crosscut, 3/8" (16 knife), s/s. (part #13322)

• Spindle Assembly, crosscut, 1/2" (12 knife), s/s. (part #13299)

• Spindle Assembly, crosscut, 3/4" (8 knife), s/s. (part #13612)

• Stripper Plate, 5/8". (part #13030)

• Stripper Plate, 5/32", julienne cut. (part #13113)

• Support Bar, clamp end. (part #12208)

• Circular and Crosscut Blades, various.

• Crosscut Spindles, 3/16", 3/8", 1/2", 3/4". (part #45202, 45227, 45266, 45366)

• Crosscut Lift. (part #45501)

• Feed Belts. (part #16918)

• Feed Drums, 3/8", 1/2", 1". (part #45299, 45300, 45302)

• Feed Rolls, 1/4", 3/8". (part #45212, 45283)

• Gears, various.

• Spacers, 5/8", 3/4", 1". (part #16109, 16110, 16121)

• Stripper Plates. (part #45075, 45240, 45285, 45296, 45312)

• Motor Pulley Assembly, 38 and 16 teeth. (part #29019)

• Slicing Wheel Assembly, 3/16" (22 knife). (part #27152)

• Slicing Wheel Assembly, 1/4" (16 knife). (part #27150)

• Slicing Wheel Assembly, 17/64" (15 knife). (part #27148)

• Slicing Wheel Assembly, 9/32" (14 knife). (part #27146)

• Slicing Wheel Assembly, 5/16" (13 knife). (part #27144)

• Ball Bearing, 35 mm ID, 62 mm OD. (part #53192)

• Bearing Assembly. (part #53199)

• Bearing Cartridge, single bearing. (part #53200)

• Bearing Holder, (part #53191)

• Bearing Holder Clamp, crosscut. (part #53113)

• Bearing Housing, jack shaft. (part #53034)

• Bearing Sleeve, replacement. (part #53198)

• End Cap. (part #53036)

• Gear, 10P, 27T, 1.125" ID, s/s. (part #53050)

• Handle Assembly, feed hopper door. (part #53451)

• Impeller Shaft. (part #53023)

• Knife, slicing, str, replacement insert. (part #52178)

• Pulley, timing, 22 teeth, DAYCO. (part #53149)

• Pulley, timing, 29 teeth, DAYCO. (part #53150)

• Pulley, timing, 38 teeth, RPP 8 mm. (part #53151)

• Pulley, timing, 88 teeth, RPP 8 mm. (part #53154)

• Pulley Hub, (used).

• Retaining Rings, w/screws. (part #53061)

• Spacer, 3/16", 2.5" OD, .058 th knife. (part #16182)

• Slicing Knife Holder, 3/16", 1/2". (part #53366, 53173)

• Spindle Assembly, circular, 3/16". (part #53364)

• Spindle Assembly, crosscut, 5/8", str, thin. (part #53377)

• Spindle Assembly, crosscut, 1", str, thin. (part #53380)

• Spindle, circular knife, w/nut. (used) (part #53109)

• Spindle, circular knife, w/ (42) 1/4" spacers and nut. (used) (part #53109)

• Spindle, crosscut, 1/4", w/retaining rings. (part #53090)

• Spindle, crosscut, 1/2", w/retaining rings. (part #53094)

• Spindle, crosscut, 1 3/4", w/retaining rings. (part #53381)

• Stipper Plate Adjustment Bar. (part #53215)

• Stipper Plate Adjustment Support. (part #53212)

• Stripper Plate, 3/32", long. (part #53441)

• Stripper Plate, 1/2", long. (part #53186)

• Stud, 3/8-16 x 1.938" long, 17-4 PH, s/s. (part #53491)

• Timken Bearing Cone, modified bore. (part #53432)

• Feed Drum, 3/16", wide slot. (part #18589)

• Feed Drum, 1/4", wide slot. (part #18582)

• Gear, 8P, 49T, 1.5" ID, nylon. (part #18023)

• Gear, 10P, 19T, .75" ID, s/s. (part #48040)

• Gear, 10P, 52T, .875" ID, MAB. (part #48039)

• Gear, 10P, 68T, 2" ID, nylon. (part #19016)

• Gear Hub, shear pin. (part #19019)

• Hub, shear pin. (part #19017)

• Hub, (part #48098)

• Impeller Shaft Assembly, (part #19272)

• Spindle Assembly, circular, 9/16", s/s, HD. (part #18599)

• Spindle Assembly, crosscut, 1/8", 24 knife, plated bronze. (part #18122)

• Spindle Assembly, crosscut, 3/16", 16 knife, plated bronze. (part #18123)

• Spindle Assembly, crosscut, 1/4", 12 knife, plated bronze. (part #18139)

• Spindle Assembly, crosscut, 3/8", 7 knife, s/s. (part #19268)

• Spindle Assembly, crosscut, 3/4", 4 knife, s/s. (part #19283)

• Cutting Wheel Assembly, julienne, 24 blade wheel w/4 julienne knives, 1 3/8" x 1 1/2" cut. (part #51052) (hub #51044)

• Cutting Wheel Assembly, julienne, 24 blade wheel w/4 julienne knives, 1 3/8" x 2" cut. (part #51314-HD) (hub #51044)

• Cutting Wheel Assembly, shredding, 22 blade wheel w/11 slicing knives and 11 julienne knives, 1/8" x 2" shred. (part #51504)

• Cutting Wheel Assembly, slicing, 24 blade wheel w/24 straight knives, 1/16" slice. (part #51046) (hub #51041)

• Cutting Wheel Assembly, slicing, 24 blade wheel w/24 straight knives, 1 1/2" slice. (part #51046) (hub #51041)

• Cutting Wheel Assembly, slicing, 22 blade wheel w/22 straight knives, 3/16" slice. (part #51047) (hub #51042)

• Cutting Wheel Assembly, slicing, 16 blade wheel w/16 straight knives, 1/4" slice. (part #51048) (hub #51043)

• Cutting Wheel Assembly, slicing, 24 blade wheel w/6 straight knives, 1" slice. (part #51049) (hub #51044)

• Cutting Wheel Assembly, slicing, 24 blade wheel w/12 straight knives, 1/2" slice. (part #51049) (hub #51044)

• Feed Belts, primary, smooth, blue. (part #51104)

• Translicer 2500, displayed w/variety of cutting wheels (over 20 cutting wheels in stock. (photo)

• Cutting Roll, 5/32", bronze. (part #38008)

• Spindle Assembly, circular, 5/32", 72 knives. (part #38017)

• Flood Tank Washer, with incline intralox belt conveyor, all s/s, 18" wide x 12' long, tank is 12' long, conveyor is lifted by cylinders for cleaning, 38" infeed 60" discharge height, 3/4HP gear head 230/460 volt motor.

• Welliver Products Rotary Washer / Scalper, 57" diameter by 136" long, s/s construction, 5/8" perforations, runs on trunions, adjustable legs.

• Wash Tank, 3' x 21' long, 15' plastic belt conveyor w/ 6" flights, incline discharge, 6' discharge height, spray bars, conveyor lift for easy cleaning. This unit was used to wash peppers and onions. (photo)

• Wash Tank, s/s product contact, plastic intralox belt (belt in fair condition), conveyor is 31" wide, tank is 37" wide ID, tank is 11' long horizontal to a 6' elevator that discharges at 4'.